[{"data":1,"prerenderedAt":126},["ShallowReactive",2],{"guide-pharmacy-robot-site-preparation-en-US":3},{"guide":4,"related":109},{"title":5,"seoTitle":6,"description":7,"summary":8,"sections":9,"faq":74,"cta":90,"date":92,"updated":92,"service":93,"order":94,"sources":95,"slug":107,"locale":108},"Preparing a pharmacy for a dispensing robot","Pharmacy Robot Installation and Leveling","NYC and Long Island pharmacy prep for a dispensing robot: cooling, power, floor load, leveling and vibration control against dropped vials, NY and DEA rules.","A pharmacy robot sets requirements that an ordinary retail fit-out does not meet. Published vendor documents call for an ambient temperature range tighter than office comfort settings, floors rated for concentrated loads, specific power and data connections, and a dust-free room at installation. In most New York buildings that means a dedicated cooling system that runs around the clock, a structural and electrical review before the lease is final, and a construction schedule that finishes the dusty trades before the robot arrives. A machine that is out of level or exposed to vibration from trains, traffic or building equipment can drop vials, so we also design the floor and support to keep it level and isolated from vibration. The vendor's site-preparation package for the exact model governs every figure.",[10,52,59,65,70],{"heading":11,"paragraphs":12,"table":15},"Start with the vendor's site package",[13,14],"We [build independent pharmacies](\u002Fservices\u002Fhealthcare) in New York City and on Long Island, including pharmacies with large robotic dispensing and storage systems that have their own cooling, environmental and power requirements. The first document we ask for is the vendor's site-preparation package for the exact model and configuration. Many dispensing-robot vendors provide their site requirements to buyers only during planning or in the purchase contract, and some issue site-specific drawings. We build to that package.","Vendors of both main classes of pharmacy automation publish general requirements, and the table below summarizes typical figures for each class. The first column describes a compact pick-and-place storage robot, a closed cabinet in which a gripper stores and retrieves medication packs on shelves. The second describes a larger automated box-picking storage system, which typically needs compressed air and three-phase power. Vendors present such figures as general guidance that site-specific drawings supersede, so the pharmacy confirms each value with its vendor's site package.",{"caption":16,"head":17,"rows":22},"Typical site requirements of two classes of pharmacy automation, and what they mean in a New York building",[18,19,20,21],"Item","Compact pick-and-place storage robot","Large automated box-picking storage system","Typical issue in NYC and Long Island",[23,28,33,38,43,47],[24,25,26,27],"Room temperature","Ambient 10 to 22 °C (50 to 72 °F); interior up to 3 °C (5 °F) warmer","Set in the vendor's site package","Landlord cooling that shuts off nights and weekends lets the room exceed 22 °C (72 °F) in summer",[29,30,31,32],"Floor","Surface load up to 600 kg\u002Fm² depending on system; leveling feet compensate up to 30 mm (about 1.2 in)","Loaded weights of several thousand pounds","600 kg\u002Fm² is about 123 lb\u002Fft², above the 50 lb\u002Fft² office and 75 lb\u002Fft² upper-floor retail live loads in the Building Code; upper floors and wood-joist buildings need an engineer's review, and unevenness beyond the leveling feet must be leveled",[34,35,36,37],"Power","Product-specific, given during planning; customer provides the power cabling","480 V 3-phase plus a 120 V circuit; more for refrigerated or dual-temperature models","Many buildings have 208 V service, so 480 V equipment needs a step-up transformer with its own space and heat",[39,40,41,42],"Other utilities","Typically none","Compressed air at 120 psi (8.3 bar) and 3 cfm; chilled water or glycol-water for dual-temperature or refrigerated models","A compressor location, condensate and piping routes must be planned with the landlord",[44,45,26,46],"Data","Flat-rate internet, RJ45 socket near the front, CAT 5 or higher","A wired drop at the machine and remote vendor support access",[48,49,50,51],"Installation conditions","Room at least 80 mm (about 3 in) higher and 50 mm (about 2 in) wider than the system; dust-free, with no concrete, drywall or screed work during installation; customer reviews fire protection","Peak sound below 70 dBA","Sprinkler heads, ducts and lights above a tall enclosure may need relocation, confirmed by the sprinkler designer",{"heading":53,"paragraphs":54},"Cooling, power and the installation window",[55,56,57,58],"A robot adds heat to a room that the base-building system was never sized for, and the 10 to 22 °C (50 to 72 °F) range typical of compact storage robots is cooler than many offices are kept in summer. We plan the robot area on its own cooling that runs continuously, with a temperature alarm, and where the pharmacy cannot tolerate a shutdown, a second unit. Published general requirements usually do not state humidity limits, so these should be requested from the vendor.","Counting and dispensing machines generate fine drug dust, which is often overlooked in pharmacy planning. We plan the room's airflow, filtration and access for filter changes so that dust does not build up on the machine's sensors and mechanisms or spread through the pharmacy, coordinated with the vendor's environmental requirements.","On the electrical side, our licensed partner electricians run dedicated circuits from a labeled, lockable panel, and the controllers and PCs go on a UPS so a short outage does not force a full restart. The vendor's guidance sets the UPS size. Network work includes a wired connection to the pharmacy management system and remote support access, kept on a network separate from guest Wi-Fi.","The robot is installed after the dusty trades are complete. Drywall dust during installation can breach the vendor's conditions, so we finish walls, ceilings and flooring first, run the cooling until the room holds its temperature, measure the delivery route through doors and elevators for the modules, and hold the room for the vendor's installation team.",{"heading":60,"paragraphs":61},"Leveling, vibration and dropped vials",[62,63,64],"Some robotic dispensers have gripper mechanisms without automatic compensation for an out-of-level cabinet or for vibration. If the machine is not level, or if it is exposed to vibration and resonance from nearby subway or elevated trains, buses and street traffic, or building HVAC equipment, the gripper can drop a vial. Dropped vials are wasted inventory, and some pharmacies stop loading expensive drugs into the machine because of that risk.","Before the machine location is fixed, we note nearby subway and elevated lines, bus routes and rooftop or ceiling-hung mechanical equipment, and we check the floor for slope and unevenness. We then design the floor and the support for the machine with common construction materials, so that they compensate for ground and building settlement and isolate the machine from building and traffic vibration.","Buildings continue to settle after the installation, so we also build simple ways to adjust the machine's leveling and to re-check it over time. In our installations this has made the dispensers noticeably more reliable and has reduced dropped vials, which saves the pharmacy money on wasted inventory.",{"heading":66,"paragraphs":67},"New York and DEA rules that shape the room",[68,69],"The State Education Department's [rules for pharmacy establishments](https:\u002F\u002Fwww.law.cornell.edu\u002Fregulations\u002Fnew-york\u002F8-NYCRR-63.6) (8 NYCRR 63.6) apply with or without automation. The registered area must be at least 300 square feet of contiguous space, with a compounding and dispensing area of at least 100 square feet that has hot and cold running water. The pharmacy needs safe drug storage, heating and ventilation adequate to safeguard the purity and potency of drugs, and a refrigerator used only for drugs, with a thermometer, holding 2 to 8 °C (36 to 46 °F). A refrigerated robot module is held to the same range and should be monitored the same way. A pharmacy inside a general merchandise store is enclosed by a permanent partition at least 9 feet 6 inches high. [The floor plan filed for registration](\u002Fguides\u002Fclinic-pharmacy-layout-patient-flow) shows the registered area, the dispensing counter, storage, the sink and the refrigerator, and [the premises are inspected before registration](https:\u002F\u002Fwww.op.nysed.gov\u002Fprofessions\u002Fpharmacy-establishments\u002Finformation\u002Finformation-and-instructions).","Federal rules require every DEA registrant to maintain effective controls against theft and diversion (21 CFR 1301.71). Under [21 CFR 1301.75(b)](https:\u002F\u002Fwww.law.cornell.edu\u002Fcfr\u002Ftext\u002F21\u002F1301.75), Schedule II to V substances are stored in a securely locked, substantially constructed cabinet, although pharmacies may instead disperse them throughout the noncontrolled stock. On the construction side, that means an anchored safe or cabinet, monitored intrusion sensors at the prescription department, access control and cameras, and a lockable partition or roll-down grille where the pharmacy shares a store. How controlled substances stored inside a robot fit these rules is a question for the pharmacist-in-charge, the vendor and DEA. New York's controlled substance rules, administered by the Bureau of Narcotic Enforcement, also apply.",{"heading":71,"paragraphs":72},"When the robot is down",[73],"A dispenser outage stops the counter. Plan manual shelving for the fastest-moving items, a UPS on the robot controller, a second cooling unit for the robot area, [a backup internet connection](\u002Fguides\u002Finternet-service-entrance-planning) for the vendor link, and a spare-parts location if the vendor recommends one. The vendor's service-response terms belong in the purchase contract, not in the construction scope.",[75,78,81,84,87],{"q":76,"a":77},"What temperature does a pharmacy robot room need?","It depends on the model. Compact storage robots typically call for an ambient temperature between 10 and 22 °C (50 and 72 °F), with the inside of the machine up to 3 °C (5 °F) warmer. Each vendor sets the exact range in its site documents. In most buildings that range calls for dedicated cooling that runs around the clock.",{"q":79,"a":80},"Can a pharmacy robot run on 208 V power?","Requirements vary by model. For compact storage robots the vendor usually provides the electrical conditions during planning, while larger box-picking systems commonly need 480 V three-phase service plus a 120 V circuit. A 480 V system in a building with 208 V service needs a step-up transformer, which takes space and adds heat. The vendor's electrical requirements for the exact configuration decide.",{"q":82,"a":83},"Does a robot change the NYSED registration of an existing pharmacy?","The registration rules do not change with automation, but a new layout can change what the filed floor plan shows. Ask the State Education Department whether a revised floor plan or an inspection is needed before rearranging a registered pharmacy.",{"q":85,"a":86},"Can the robot be installed while the rest of the pharmacy is under construction?","Not under typical vendor conditions, which require a dust-free site with no concrete, drywall or screed work during installation. We schedule the robot after finishes and after the cooling has been running steadily.",{"q":88,"a":89},"Why does a pharmacy robot drop vials?","On some robotic dispensers the gripper does not automatically compensate for an out-of-level cabinet or for vibration. A machine that is not level, or that is exposed to vibration from nearby trains, street traffic or building HVAC equipment, can drop vials, which become wasted inventory. We design the floor and support to compensate for settlement and isolate the machine from vibration, and we build in a simple way to adjust and re-check its leveling over time.",{"text":91},"Send the floor plan, the dispenser make, model and configuration, the vendor's site-preparation package, photos of the floor at the planned location, and the location of any nearby subway or elevated lines and rooftop mechanical equipment. You receive, at no charge, the vendor's power, cooling, floor-load and network requirements checked against your space, a review of the leveling and vibration risks at that location, the items that need an engineer's review, and a budget range scheduled around the installation date.","2026-10-25","healthcare",127,[96,100,104],{"title":97,"url":98,"publisher":99},"N.Y. Comp. Codes R. & Regs. Tit. 8 § 63.6 - Registration and operation of New York establishments","https:\u002F\u002Fwww.law.cornell.edu\u002Fregulations\u002Fnew-york\u002F8-NYCRR-63.6","Cornell Law School, Legal Information Institute",{"title":101,"url":102,"publisher":103},"NYS Pharmacy: Pharmacy Establishments: Registration Application Requirements & Forms: Information and Instructions","https:\u002F\u002Fwww.op.nysed.gov\u002Fprofessions\u002Fpharmacy-establishments\u002Finformation\u002Finformation-and-instructions","NYS Education Department, Office of the Professions",{"title":105,"url":106,"publisher":99},"21 CFR § 1301.75 - Physical security controls for practitioners","https:\u002F\u002Fwww.law.cornell.edu\u002Fcfr\u002Ftext\u002F21\u002F1301.75","pharmacy-robot-site-preparation","en-US",[110,114,118,122],{"slug":111,"title":112,"description":113,"service":93,"date":92,"updated":92},"clinic-lease-checklist-nyc-long-island","Before you sign a clinic lease in NYC or Long Island","What to settle before leasing clinic space in NYC or Long Island: occupancy, Article 28, the certificate of occupancy and what the building can supply.",{"slug":115,"title":116,"description":117,"service":93,"date":92,"updated":92},"hipaa-physical-safeguards-clinic-design","Designing a clinic around HIPAA physical safeguards","How door hardware, cameras, workstation placement, a secure network closet and separated networks in a NYC clinic support the HIPAA Security Rule.",{"slug":119,"title":120,"description":121,"service":93,"date":92,"updated":92},"clinic-backup-power-vaccine-network","Keeping a clinic open through a power or network outage","Vaccine refrigerator outlets, UPS and generator options, a critical-load panel, internet failover and HVAC redundancy for NYC and Long Island clinics.",{"slug":123,"title":124,"description":125,"service":93,"date":92,"updated":92},"clinic-ventilation-filtration-nyc","Clinic ventilation and filtration in NYC and Long Island","What NYC and Long Island codes require for clinic ventilation, where ASHRAE 170 applies, MERV 13 vs HEPA, waiting-room pressure and filter access.",1792938766948]